flexiblefullpage -
billboard - default
interstitial1 - interstitial
catfish1 - bottom
Currently Reading

Fannie Mae green bonds program could be greenwashing

Codes and Standards

Fannie Mae green bonds program could be greenwashing

Analysis shows significant number of green bond properties become less efficient.


By Peter Fabris, Contributing Editor | August 18, 2021
Green leaves

Courtesy Pixabay

Fannie Mae’s green bond program to spur efficiency upgrades may be falling far short of its goals, according to analysis by Grist.

Grist report says that about 1,600 of the 3,800 properties that had loans packaged into “green” mortgage-backed securities saw improvement in their energy scores within a median period of about two years. But more than 800 properties that the online publication examined saw lower or identical energy scores in the most recent data year compared to their scores at loan issuance.

“Whether or not Fannie Mae’s green bonds program is driving significant decarbonization and efficiency improvements is very much an open question,” Grist says. “The value of the program is unclear even in cases where energy savings did improve: About a fifth of the buildings enrolled from 2016 through 2019 performed worse than the median U.S. building even after fulfilling program requirements.”

Another criticism: Participation is highest in states and cities that already have stringent building energy efficiency codes. That means some of these building owners may have pursued green improvements without Fannie Mae’s incentives.

Related Stories

| Jan 16, 2013

New standard for geothermal heat pump systems piping to be included in 2015 International Mechanical Code

NSF International, an independent global organization that writes standards, and tests and certifies products, has published the first in a series of American National Standards for Ground-Source Geothermal Piping Systems – NSF/ANSI 358-1.

| Jan 16, 2013

ANSI passes new safety standards for reinforcing steel and post-tensioning

The ANSI A10 Accredited Standards Committee for Construction and Demolition Operations recently approved amendments to the ANSI A10.9 Concrete and Masonry Standard.

| Jan 8, 2013

Congress passes Drywall Safety Act

Congress recently passed the Drywall Safety Act; President Barack Obama is expected to sign it soon.

| Jan 8, 2013

Building-integrated PVs could help boost green standards over the next few years

A developing technology could begin to have an impact on sustainable standards over the next few years.

| Jan 8, 2013

Revamp of codes among nine low tech steps to raise community resiliency

Updating of local zoning and building codes is one of nine low-tech steps that can boost sustainability and storm resiliency, according to this article.

| Jan 8, 2013

Group releases safety and building codes from 24 countries

Public.Resource.Org released 10,062 public safety documents including building codes covering 24 countries and 6 regions.

| Jan 8, 2013

Montana developing high-performance building standards for state projects

The Montana Department of Administration is developing a single building standard for all state facilities, and hopes to have a plan in place this spring.

| Jan 4, 2013

AGC economist says "fiscal cliff" deal will give construction a boost

The deal in Congress to avoid going over the so-called fiscal cliff "should encourage many businesses to go ahead with projects they have held in reserve," said Ken Simonson, chief economist of the Associated General Contractors of America.

| Jan 4, 2013

California standards on furnishings, insulation to be revised

California is revising the state’s standards on interior furniture and insulation to maintain or improve fire safety while reducing or eliminating the use of toxic chemicals.

| Jan 4, 2013

Tilt-Up Concrete Association releases new temporary wind bracing guidelines

The Tilt-Up Concrete Association has released revised guidelines on Temporary Wind Bracing of Tilt-Up Concrete Panels During Construction. 

boombox1 - default
boombox2 -
native1 -

More In Category


AEC Tech

Lack of organizational readiness is biggest hurdle to artificial intelligence adoption

Managers of companies in the industrial sector, including construction, have bought the hype of artificial intelligence (AI) as a transformative technology, but their organizations are not ready to realize its promise, according to research from IFS, a global cloud enterprise software company. An IFS survey of 1,700 senior decision-makers found that 84% of executives anticipate massive organizational benefits from AI. 


Codes and Standards

Updated document details methods of testing fenestration for exterior walls

The Fenestration and Glazing Industry Alliance (FGIA) updated a document serving a recommended practice for determining test methodology for laboratory and field testing of exterior wall systems. The document pertains to products covered by an AAMA standard such as curtain walls, storefronts, window walls, and sloped glazing. AAMA 501-24, Methods of Test for Exterior Walls was last updated in 2015. 


MFPRO+ News

World’s largest 3D printer could create entire neighborhoods

The University of Maine recently unveiled the world’s largest 3D printer said to be able to create entire neighborhoods. The machine is four times larger than a preceding model that was first tested in 2019. The older model was used to create a 600 sf single-family home made of recyclable wood fiber and bio-resin materials.

halfpage1 -

Most Popular Content

  1. 2021 Giants 400 Report
  2. Top 150 Architecture Firms for 2019
  3. 13 projects that represent the future of affordable housing
  4. Sagrada Familia completion date pushed back due to coronavirus
  5. Top 160 Architecture Firms 2021