flexiblefullpage -
billboard - default
interstitial1 - interstitial
Currently Reading

26 ways to prevent cracks in brickwork

billboard - default
interstitial1 - interstitial
BD+C University Course

26 ways to prevent cracks in brickwork

This continuing education course describes numerous ways designers, mason, and contractors can prevent cracks in brickwork due primarily to elastic deformation of the brick.


Provided By: BD+C
By Brian Trimble, PE, LEED AP; James Tann; and Charles Clark, AIA, PE March 9, 2022
26 ways to prevent cracks in brickwork, BD+C University

Changes in temperature or moisture can wreak havoc on building materials, and brick is no exception. Elastic deformation due to loads, creep, or changes in volume can cause movement, which can crack your project's lovely brickwork. 

There are two basic ways to avoid cracks in brick work: 1) minimize the movement, or 2) accommodate movement between materials and assemblies, through a system of movement joints that allow for some give in your brickwork.

THE BASICS OF EXPANSION JOINTS IN BRICKWORK

1. Be aware that brick can change slightly in volume, depending on the age and color of the brick, the direction the wall faces, and the temperature at installation.

2. Assume that bricks will increase slightly in size over their life. This is due primarily to moisture expansion and, says coauthor Brian E. Trimble, “it’s part of how bricks are made.” Brick Industry Association (BIA) Technical Note 18 has helpful formulas for calculating the movement of brick walls.

3. Use expansion joints in your brickwork. Expansion joints separate brick masonry into segments to prevent cracking caused by temperature change, moisture expansion, elastic deformation, settlement, or creep. They can be horizontal or vertical.

4. Don’t confuse expansion joints with control joints. According to BIA Technical Note 18A, the term “control joint” is used in reference to concrete or concrete masonry construction. A “building expansion joint” is a through-the-building joint that separates a building into discrete sections to relieve stress. A “construction joint” (or “cold joint”) is used primarily in concrete work when construction is interrupted.

5. Form the expansion joint correctly, by leaving a continuous unobstructed opening through the brick wythe and filling it with a highly compressible material, preferably premolded foam or neoprene pad. A backer rod and sealant are used out front to weatherproof the joint.

 


Most of the expansion of fired brick due to moisture occurs in the first year of installation.

 


Graphic shows various methods for installing vertical expansion joints, as recommended by the Brick Industry Association. Source: BIA

 

6. Make sure all expansion joint materials extend through the full thickness of the wythe to keep mortar and other debris from clogging the joint and block water from penetrating the joint as much as possible.

7. Don’t use fiberboard or similar materials in expansion joints; they are not compressible.

8. Don’t allow mortar, ties, or wire reinforcement to extend into or bridge the expansion joint, as these materials can restrict movement and undo the benefit of the expansion joint.

HOW TO APPLY VERTICAL EXPANSION JOINTS

9. Be aware that the positioning and spacing of expansion joints in brickwork will vary from structure to structure, depending on a variety of factors: the amount of expected movement, the size of the expansion joint, the compressibility of the expansion joint materials, restraint conditions, elastic deformation due to loads, shrinkage and creep of mortar, construction tolerances, and wall orientation. “There’s something of an art to getting this right,” says Trimble.

10. Don’t go more than 20 feet without a vertical expansion joint for brickwork in a veneer or cavity wall. For brickwork without openings, place expansion joints no more than 25 feet apart. “This is a well-accepted rule of thumb in the industry,” says co-author James Tann. 

11. Don’t leave it up to the masons to position the expansion joints. “The design professional should take responsibility for determining the placement and spacing of joints,” says Trimble.

 


Graphic illustrates the correct method for locating an expansion joint in a lipped brick course, which is used to allow movement while reducing the potential negative aesthetic impact of the expansion joint.

 

12. Prioritize expansion joint placement in areas of high stress concentration, where cracking is most likely to occur. Starting at a corner and placing joints at the typical spacing around the building perimeter is not recommended.

Tip: Begin placement at material transitions, junctions, and offsets before placing at an outside corner. By placing expansion joints at these high-priority areas first, only a few expansion joints, if any, will be required to meet the maximum spacing recommendations. For step-by-step details, refer to BIA Technical Note 18A, page 7. 

13. Place vertical expansion joints at or near corners (outside and inside), offsets and setbacks, openings, wall intersections, changes in wall heights, and parapets. For corners, place an expansion joint within at least 10 feet of the corner on at least one of the two walls. 

14. Place expansion joints at the junction of walls with different environmental or climatic exposures or support conditions.

Tip: Use expansion joints to separate adjacent brick walls of different heights to avoid cracking caused by differential movement. The joint can be placed at the interior corner or, if appropriate, a foot or so away from the corner to provide a masonry bonded corner for stability.

Note: Wall ties must be in place to properly support the brick wythes adjacent to the interior corner.

ADDRESSING HORIZONTAL EXPANSION JOINTS IN BRICKWORK

According to BIA Technical Note 18A, “Horizontal expansion joints are typically needed if the brick wythe is supported on a shelf angle attached to the frame or used as infill within the frame. Placing horizontal expansion joints below shelf angles provides space for vertical expansion of the brickwork below and deformation of the shelf angle and the structure to which it is attached.”

15. Provide horizontal expansion joints under each shelf angle in structures that support the brick wythe on shelf angles. 

16. Remove temporary shims that may have been used to support the shelf angle during construction.

Two techniques for proper installation of thin brick movement joints. For best results with thin brick projects, follow Brick Industry Association Technical Note 28C.

 

17. Consider using a “lipped” brick course in cases where you see the need for a large horizontal expansion joint. Lipped bricks allow movement while reducing the potential negative aesthetic impact of the joint.

Tip: To avoid breakage, the height and depth of the lipped portion of the brick should be at least a half-inch (13mm).

Caution: For quality assurance, have your lipped brick made by your brick manufacturer. “Masons can saw cut a lip brick from a standard unit, but this is not as precise as what manufacturers can do. Overcutting, often performed when field fabricating lipped brick, can cause the cut units to fail,” warns Tann.

18. Be sure to evaluate the movement tolerances of adjacent materials, including the building frame itself. This is especially true for an anchored brick veneer with a wood frame backing when its height exceeds 30 feet. Additional detailing may be required to address the shrinkage of the wood.

For more information, refer to BIA Brick Brief: “Designing Anchored Brick Veneer Above 30 feet with a Backing of Wood Framing”

19. Don’t allow contact at any time between the lipped brick and the brickwork below the shelf angle or between the lip of the brick and the shelf angle.

ADDITIONAL FACTORS TO CONSIDER IN BRICK CONSTRUCTION

20. Consider ways to make expansion joints less noticeable, especially on long, flat walls.

Tip: Try using architectural features such as quoins, recessed panels of brickwork, or a change in bond pattern to reduce any negative effect. Or you might go so far as to call attention to the expansion joint by recessing the brickwork at the joint, or by using special-shaped bricks.

21. Try to locate expansion joints at inside corners, where they are less noticeable.

22. Don’t hide expansion joints behind downspouts or other key building elements, unless you want to get a lot of nasty calls from the building's maintenance department.

23. Don’t “tooth” expansion joints to follow the masonry bond pattern. This practice makes it harder to keep debris out of the joint during construction; such debris can interfere with the proper movement of the joint.

24. Consider the use of expansion joints in reinforced brick walls. “While the reinforcing aids in resisting movement, expansion joints at traditional placements can reduce stress concentrations in the masonry, as well as the potential for cracking,” says coauthor Charles (Chip) Clark.

25. Provide expansion joints in thin brick applications, per BIA Technical Note 28C. BIA Technical Note 28C on expansion joint placement in thin brick recommends the following: Extend movement joints through the thickness of the entire veneer assembly, for the full length or height of the veneer, including parapets. Space joints no more than 18 feet (5.5 meters) on center in either direction.

The maximum area between movement joints should not exceed 144 sf (13.4 square meters) or a length-to-height or height-to-length ratio of 2½:1. Align veneer movement joints directly over substrate movement joints.

For proprietary modular and prefabricated thin brick panels, follow manufacturer’s instructions.

26. Study the BIA Technical Notes. Technical Note 18 (“Volume Changes – Analysis and Effects of Movement”), Technical Note 18A (“Accommodating Expansion of Brickwork”), and Technical Note 28C (“Thin Brick Veneer”) at: www.gobrick.com/read-research/technical-notes.      

About the Authors
Brian E. Trimble, PE, CDT, LEED AP, FASTM, former Senior Director of Engineering Services and Architectural Outreach at the Brick Industry Association, is Director of Industry Development, International Masonry Institute. James A. Tann, FASTM, Past President of the Brick Institute of America–Mid East Region and former Member of the Board of Directors of ASTM International, is Director of Technical Services, Belden Brick Co. Charles (Chip) Clark, AIA, PE, LEED AP, is Vice President of Engineering Services, the Brick Industry Association.

Ready to put your knowledge to the test?

Don’t have an account? Click here to register for a free account now!

Tags

More Courses

Interior design/Interior architecture

6 steps to designing a modern wine display

Design-focused wine displays are becoming increasingly popular in amazing residential and commercial properties throughout the world. Top design/…

Classroom Sponsor - PROVIDED BY: VintageView Wine Storage Systems
Exterior

Design guide for parapets: Safety, continuity, and the building code

Originally designed to protect against enemy attack, the parapet in modern construction is far removed from its antiquated roots. Though the word…

Campus Sponsor - PROVIDED BY: BD+C
Structural

Designing smarter places of learning

Steel building systems provide unique advantages in the construction of education facilities. This introductory course explains these benefits can be…

Campus Sponsor - PROVIDED BY: New Millennium Building Systems
Structural

Choosing the right paver system for rooftop amenity spaces

Since the industrial revolution, the United States has been rapidly urbanizing. The most recent census data shows that approximately 80% of Americans…

Campus Sponsor - PROVIDED BY: BD+C
Exterior

Designing with architectural insulated metal wall panels

Insulated metal wall panels (IMPs) offer a sleek, modern, and lightweight envelope system that is highly customizable. This continuing education…

Classroom Sponsor - PROVIDED BY: Metl-Span
Land Development

Planning for hospital campus access that works for people

Well-functioning hospitals and medical centers are no accident that a team of healthcare professionals bandaged and fixed up in the emergency room.…

Campus Sponsor - PROVIDED BY: BD+C
1.0 AIA LU/HSW

For glass openings, how big is too big?

Advances in glazing materials and glass building systems offer a seemingly unlimited horizon for not only glass performance, but also for the size…

Campus Sponsor - PROVIDED BY: BD+C
Exterior

New ideas in glass curtain walls, window walls, and storefronts

Driven by two distinct influences, a new generation of glass building enclosures has a unique trajectory—toward higher performance and sustainability…

Campus Sponsor - PROVIDED BY: Azon
1.0 AIA LU

12 factors to consider in evaluating tankless water heaters for multifamily housing projects

Tankless water heaters have come a long way in the last 10 years or so. One-third of respondents (33.2%) to our exclusive 2019 Multifamily Design+…

Campus Sponsor - PROVIDED BY: BD+C
1.0 AIA LU/HSW

Multifamily security design tips from four certified security professionals

We asked four top experts—all members of the International Association of Professional Security Consultants (IAPSC)—for their advice on securing…

Campus Sponsor - PROVIDED BY: BD+C

Learning Objective

After reading this article, you should be able to:

  • LIST several physical characteristics and properties of brick that can affect brickwork installation and longevity.
  • DESCRIBE the proper location of horizontal and vertical expansion joints in brickwork.
  • DISCUSS the use of a “lipped” brick course when a large horizontal expansion joint is called for.
  • DELINEATE the technical factors for locating expansion joints in thin brick applications according to Brick Industry Association Technical Note 28C.

boombox2 -
native1 -

More In Category


BD+C University Course

Designing with architectural insulated metal wall panels

Insulated metal wall panels (IMPs) offer a sleek, modern, and lightweight envelope system that is highly customizable. This continuing education course explores the characteristics of insulated metal wall panels, including how they can offer a six-in-one design solution. Discussions also include design options, installation processes, code compliance, sustainability, and available warranties.



BD+C University Course

Design strategies for metal wall and roof systems

Versatility, reliable performance, and relatively low installed-costs make prefabricated metal panel wall and roof systems attractive for sophisticated building applications. Owners and architects often collaborate to use these products in distinctive and aesthetically innovative design solutions. Manufacturers, recognizing an opportunity, have expanded their product lines with the aim of amplifying product use across a range of building types. Of course, no building enclosure system is without design challenges and considerations.

halfpage1 -

Most Popular Content

  1. 2021 Giants 400 Report
  2. Top 150 Architecture Firms for 2019
  3. 13 projects that represent the future of affordable housing
  4. Sagrada Familia completion date pushed back due to coronavirus
  5. Top 160 Architecture Firms 2021

 


Magazine Subscription
Subscribe

Get our Newsletters

Each day, our editors assemble the latest breaking industry news, hottest trends, and most relevant research, delivered to your inbox.

Subscribe

Follow BD+C: